ADDITIONAL DOCUMENTATION

11.10-1 Contact Customer Care at 1.844.4HYTROL Important application information for zero-pressure conveyors. When applying any zero-pressure conveyor, a number of factors must be considered for the conveyor to operate properly.

PRODUCT WEIGHT

138-NSPEZ - Maximum load 10 lbs. per driven roller. No minimum weight requirement. 190-NSPEZ - Maximum load 15 lbs. per driven roller. Minimum load 1 lb. per foot of conveyor. No minimum weight requirement. ABEZ - Maximum load per linear foot of conveyor is 150 lbs., NOT TO EXCEED the capacity shown in catalog. No minimum weight requirement. 190-E24EZ - Maximum load of conveyor is 50 lbs. per zone, NOT TO EXCEED the capacity shown in Hytrol's general catalog. No Minimum weight requirement 25-LREZ - Maximum load per linear foot of conveyor is 1000 lbs., NOT TO EXCEED 4000 lbs. unit load or total load capacity shown in Hytrol's general catalog. 199-CREZD - Maximum unit load 1250 lbs. at 35 FPM (1/2 HP maximum). NOT TO EXCEED CAPACITY shown in Hytrol's general catalog. 25-CREZD - Maximum unit load 3000 lbs. at 30 FPM (1/2 HP maximum). NOT TO EXCEED CAPACITY shown in Hytrol's general catalog. 36-CREZD - Maximum unit load 5000 lbs. at 26.5 FPM (1/2 HP maximum). NOT TO EXCEED CAPACITY shown in Hytrol's general catalog. PLEZD - Maximum unit load 2000 lbs. at 38 FPM (1/2 HP maximum). NOT TO EXCEED CAPACITY shown in Hytrol's general catalog. DCEZ-60, DCEZ-63 - Maximum load 6000 lbs. at 30 FPM (1 1/2 HP maximum). NOT TO EXCEED CAPACITY shown in Hytrol's general catalog. DCEZ-82, DCEZ-83 - Maximum load 6000 lbs. at 30 FPM (2 HP maximum). NOT TO EXCEED CAPACITY shown in Hytrol's general catalog.

MINIMUM PRODUCT LENGTH

Minimum product length on zero-pressure package handling conveyors should be three times the tread roller spacing. Based on the standard roller spacing of 3 in., this would be 9 in. Minimum product length on zero- pressure pallet handling conveyors should be four times the tread roller spacing.

MAXIMUM PRODUCT LENGTH

Maximum product length on zero-pressure package handling conveyors should be 3 in. less than the zone length. There will be no gaps between products if the product length equals the zone length. Maximum product length on zero- pressure pallet handling conveyors should be 6 in. less than the zone length.

PRODUCT WIDTH

Product not to be wider then the Between Rail Width of the conveyor on zero-pressure package handling conveyor. Note: Product clearance must be checked if zero-pressure curves are used in the application.

CONDITION OF PRODUCT

BOTTOM

A firm flat bottom is required on product. A soft or irregular bottom may cause hang-up. If the load exceeds 50 lbs. per foot, product should have a rigid bottom. Pallet type products must have a conveyable surface with runners in the direction of travel.

PRODUCT SHAPE

Containers with handles, product overhang, or of v-shaped design may leave gaps at sensor (see illustration below). If sensor is not depressed, or blocked, in the case of photoelectric sensors, a pressure build-up will occur.

PRODUCT FLOW

All of Hytrol's zero-pressure conveyors are designed for one direction conveying only. For reversing, contact factory.

CONVEYING SPEED

Speeds other than the standard speed listed in the specifications for each conveyor will affect the accumulation feature of the conveyor.

BED LENGTHS

Bed lengths are supplied in multiples of zone length. Because of special design equipment, standard bed lengths must be used to make up Overall Conveyor Length. Adjoining conveyors should be altered to fit layout requirements.

PAN WITH LOAD CONTAINER WITH LIP V-SHAPED CONTAINER WITH HANDLES

GAP

EZ LOGIC MODULES

GAP

POWERED CONVEYORS

Previous Page
Next Page