2.1-4 Contact Customer Care at 1.844.4HYTROL
FLOOR SUPPORTS - MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. BELT * - White Polymate 100 RMP-COS (cover one side), Black Trackmate 120 Roughtop with PVC cover, Brown Polymate Roughtop w/Nitrile cover, Black Trackmate 533 COS-PVC, Tan Glidetop, Pure Gum Rubber Roughtop. Incline units: Black Trackmate 120 High-Grip Longitudinal Groove. BELT SPEED * - Other constant and variable speeds. V-belt drive supplied under 17 FPM. SHAFT-MOUNTED END DRIVE - Motor reducer unit mounted on extended drive pulley shaft. Can be mounted with motor horizontal for 4 7/8 in. minimum elevation. Mounting bracket and torque arm allows for multiple mounting positions. 4 in. drive only. See chart page 30 for speeds. OVERHEAD END DRIVE - Motor-reducer unit mounted 9 1/2 in. above belt. Other clearances available, specify. Chain guard right hand side. Minimum elevation 6 in. with 4 in. drive, 10 in. with 8 in. drive. SIDE MOUNTED END DRIVE - Motor-reducer unit mounted on left hand side of conveyor. Minimum elevation 7 in. with 4 in. drive, 10 in. with 8 in. drive. CENTER DRIVE - Provides 16 in. of belt take-up. Minimum elevation 16 in. with 4 in. drive, 17 in. with 8 in. drive. Specify location. Minimum OAL without modification is 66 in. with 4 in. drive, 66 in. with 8 in. drive. Belt width is 6 in. less than bed width. LOW ELEVATION SIDE MOUNTED CENTER DRIVE - Motor-reducer unit mounted to side of conveyor. Minimum elevation 13 1/2 in. with 4 in. or 8 in. drive. Belt width is 6 in. less than bed width. STACKED END DRIVE - Minimum elevation 27 3/4 in. with v-belt drive, 33 3/4 in. with C-face drive. V-BELT DRIVE - V-belt supplied between motor and reducer. Minimum overall drive width 14 in. Allow 65 in. O-RING DRIVE CHAIN - With sealed-in lubricant Recommended for applications that do not permit regular lubrication. UNDERSIDE TAKE-UP - Provides 16 in. of belt take- up. Extends down 13 1/8 in. from top of belt. Belt width is 6 in. less than bed width. SIDE TABLES - Powder-painted 14 ga. formed steel table, 10 in., 16 in., or 22 in. wide from side of bed. One or both sides. GUARD RAILS - Universal adjustable universal channel, solid side guards, PC side guards with formed top. Fixed Channel overlapping, one direction (use with systems ends only). Fixed Channel non- overlapping, reversing (use with system ends only). NOSEOVER * - Adjustable, single (0 to 15), double (0 to 30). LOW POWERED FEEDER * - Chain type driven from tail pulley of inclined conveyor. Underside take- up required when end drive is used. MS-Type floor supports supplied as optional equipment. 8 in. dia. drive recommended on conveyor when feeder exceeds 44 1/2 in. OAL-50 1/2 in. OAL with system end. GRAVITY BRACKETS - Adjustable bars with 1 in. dia. pop-out transfer roller to attach wheel or 1 3/8 in. roller conveyor. Available 12 in. to 28 in. bed widths only. BUTT COUPLINGS - Provides connection to SB, RB, LR, ACC, ACZ, ABEZ, 190-NSP, 190-NSPEZ, 1.9 in. and 2.0 in. gravity conveyors. Includes 1 in. dia. pop-out roller. Center drive or underside take-up recommended. SYSTEM END ROLLER - 12 in. long tail sections provide connection to SB, RB, LR, ACC, ACZ, ABEZ, 190-NSP, 190-NSPEZ, 1.9 in. and 2.0 in. gravity conveyors. Includes 1.9 in. dia. pop-out transfer roller. Belt width is 6 in. less than bed width. Center drive or underside take-up required. Not available on 10 in. bed. PULLEYS - 6 in. tail with 1 3/16 in. dia. shaft at bearings, or 8 in. drive with 1 3/16 in. dia. shaft at bearings. CASTERS - See Accessory section. POLY-TIER SUPPORTS - 36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied. CEILING HANGER - 5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available. MOTOR - Energy efficient, single phase, brakemotor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS - One direction manual start switch, reverse drum switch, non-reversing and reversible magnetic starters, push button stations. AC variable frequency drive. * Note : Capacity affected with these options.
Optional EquipmentPrevious Page