190-E24 & 190-E24C

Optional Equipment

FLOOR SUPPORTS - MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support. POWER SUPPLY (MOTORS) - 20 Amp power supply available, 20 motors maximum. 5 Amp power supply available, 3 motors maximum. 480 Volt Power Supplies also available. POLY-TIER SUPPORTS - 36 in. to 120 in. support heights in 6 in. increments. Knee braces required. CEILING HANGER - 5/8 in. dia. x 8 ft. long unplated steel rods fully threaded. Other lengths and galvanized rods available. GUARD RAILS - Adjustable Universal Channel Guard Rail, type A and B angle (see Accessory section). Note: If product comes in contact with guard rails, product flow will be affected. MOTOR AND SEPARATE CONTROL CARD - Available with 3 Amp setting. TANGENTS - Slaved and Powered type available. Motors mounted on outside of channel. BED (E24) - Roller bed with 1.9 in. dia. roller x 16 ga. galvanized tube and bearings spaced every 3 in. Mounted set-high in 6 1/2 in x 12 ga. powder-painted formed steel channel frame, bolted together with splice plates. BED (E24C) - Roller bed with 2 1/2 in. dia. tapered to 1 11/16 in. dia. x 14 ga. galvanized rollers. Mounted in 6 1/2 in. x 12 ga. powder-painted formed steel channel frame. MOTOR - 24VDC motor with integrated control card located along section on the inside of the BR on straight section only. Maximum slaved rollers is 16 per each motor. SLAVE O-RINGS - 3/16 in. dia. polyurethane o-rings slave-driven tread rollers from motor. POWER SUPPLY (FOR MOTORS) - 40 Amp DC power supply, 24 volt fixed output. Maximum of 40 motors per power supply. 12VA, 8.6 Amp input. Mounted near center of conveyor. Note: Number of motors per power supply is based on the use of standard Hytrol o-rings. Other o-rings are available that may increase load capacity, but reduce the number of motors that may be powered from one power supply. Contact factory for more information. CONVEYING SPEED - 25 to 254 FPM, set on integrated motor control card. CROSS BRACKING - Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and ensure correct product tracking. Supplied to section adjoining drive and every other section, 20 ft. bed lengths and over. Supplied on bed lengths 9 ft. and over. CAPACITY - Maximum 37 lbs. per foot with a maximum capacity per E24 motor of 75 lbs. If loading product back- to-back use the following chart: FLOOR SUPPORTS - Supplied as optional equipment. Note: Capacity is based on the use of standard Hytrol o-rings. Other o-rings are available that may increase load capacity, but reduce the number of motors that may be powered from one power supply. Contact factory for more information.

TRANSPORT LIVE ROLLER

9.1-2 Contact Customer Care at 1.844.4HYTROL

Standard Specifications

Section Length Number of Motors in Section Capacity (lbs. per foot) 2' 0" 1 37 2' 6" 30 3' 0" 25 3' 6" 21 4' 0" 19 4' 6" 2 33 5' 0" 30 5' 6" 27 6' 0" 25 6' 6" 23 7' 0" 21 7' 6" 20 8' 0" 19 8' 6" 3 26 9' 0" 25 9' 6" 23 10' 0" 22

Previous Page
Next Page